Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: wanting to abandon the project

  1. #1
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    wanting to abandon the project

    After visiting jdinner’s shop and looking at his progress on the chassis and how it looked in person I have decided to abandon this project before I get to involved with it. I have replaced all the body mounts and trial fitted the body. Everything that comes with the price is listed bellow I would be willing to separate if I can recoup most of my investment. The car is located in Canada about 2 hrs from Buffalo and 3 hrs from Detroit.

    The Donor car (84' frame with 86' v6 electronics and engine. A/C, 4spd manual transmission Power Everything, front nose support welded in, hood hinged, frame already re-enforcements. Aftermarket power locks hooked into alarm.

    Calipers, all 4 corners
    Rotors, All 4 Corners
    Pads, all 4 Corners
    Clutch
    Water pump
    Bearings, Front
    Drive Axle, CV Joint and Tranny Seal
    EGR Tube
    Distributor (Cap, Rotor, Pickup coil)
    Shift cable
    TPS Sensor
    MAP Sensor
    Ignition Lock Cylinder
    Ball Joint, Rear left
    Door Lock Actuators
    Prestige (Audiovox) Alarm System w/ starter disable
    1.5" Suspension Techniques Lowering Springs
    Battery
    Aftermarket Rearview mirror with Map Lights
    four tail lights
    two turn signals
    two "H4" headlight housing w/ bulbs
    Ferrari "style" wheel centers/ registration stickers
    4 Wheel Spacers

    $5,200.00 U.S. or $6,250.00 Canadian

    You can email me at robw@supersan.on.ca or call 519-465-7999

  2. #2
    Senior Member superstang460's Avatar
    Join Date
    Apr 2004
    Posts
    1,590

    Re: wanting to abandon the project

    You want to through in the towel so soon? Didn't you just get this project from Ari? I'm sorry to hear that, but totally understand. I'm still trying to sell my 355 coupe for $4000 or best offer and just cut my losses before I go in deeper. Again, sorry to hear this but you have to do what you have to do. :-\
    Best of luck.

    Bob
    5 out of 4 people are not good at fractions

  3. #3
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    You are right I did buy it from Ari just a few months ago. But that was before I saw jim's work on his web site but after going out and seeing it last week that was the final nail in the coffin.. I know a guy that will complete the car for me for around 8000 canadian in about a 6 weeks but I didn't see the point if my hart was on a custom chassis to finish this car just to sell it. if that doesn't work that I will just work on it in my own spare time and since my labour doesn't cost anything.

  4. #4
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    I will even share my garage... with heat...over the winter for the right person.. ;D

  5. #5
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    Here are few pic's



  6. #6
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    Looking for 4500.00 U.S. or 5500.00 Cdn

  7. #7
    Senior Member
    Join Date
    Oct 2004
    Posts
    112

    Re: wanting to abandon the project

    possibly interested, who makes that body kit? Is it 3" stretch, or non-stretched version? And most important, seperate rockers?
    Darren

  8. #8
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    Sorry non strech but I do have access to a strech rear end for 1200 and also no seperate rockers

  9. #9
    Senior Member
    Join Date
    Oct 2004
    Posts
    112

    Re: wanting to abandon the project

    If the chassis is stretched, will the rear section of the body still fit? Who makes the body kit?
    Darren

  10. #10
    Junior Member
    Join Date
    Sep 2004
    Posts
    23

    Re: wanting to abandon the project

    If you streched the rear of the car, you would have to strech the body or buy a new rear clip. I can have the body streched for you for free but.. It would depend on the sale

Similar Threads

  1. anyone wanting to buy diablo bodies
    By cliffscustomfab in forum The Mall
    Replies: 14
    Last Post: 10-06-2011, 07:38 AM
  2. Wanting some g28 interior door panels
    By lambochik in forum The Mall
    Replies: 24
    Last Post: 07-20-2011, 09:02 PM
  3. Wanting to buy a used replica privately but need financing
    By ferraristyle in forum Technical Discussion & Question
    Replies: 11
    Last Post: 10-31-2005, 12:48 PM
  4. wanting a wide track susp..
    By blutes in forum The Mall
    Replies: 10
    Last Post: 01-06-2005, 09:20 PM
  5. Wanting to know who has molds for...
    By GSXRBOBBY in forum General Kitcar Chat
    Replies: 0
    Last Post: 12-31-2003, 06:41 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •