Search:

Type: Posts; User: txbuilder

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    378

    The 2.3 Pinto/Mustang II engine might bolt up. ...

    The 2.3 Pinto/Mustang II engine might bolt up. If not, swapping the transmission shouldn't be hard. Should be lots of those available at a reasonable price.
  2. Replies
    14
    Views
    1,002

    Yes, I have done several adapters for that...

    Yes, I have done several adapters for that combination.
  3. Replies
    14
    Views
    1,002

    The 5-speed from the Boxster is rather weak and I...

    The 5-speed from the Boxster is rather weak and I would not recommend using one with an engine making much HP. They fail frequently with the stock Boxster engine.
  4. Replies
    14
    Views
    1,002

    This can be done with the Audi 01X transmission...

    This can be done with the Audi 01X transmission or with the front wheel drive only 01E. The AWD Audi transaxle does not lend itself to be converted to two wheel drive only and you can't use the AWD...
  5. Replies
    2
    Views
    193

    I have a 1990 model. Runs great. 50MPG

    I have a 1990 model. Runs great. 50MPG
  6. Replies
    44
    Views
    3,596

    If your master cylinder is above the wheel...

    If your master cylinder is above the wheel cylinders all you need is a proportioning valve to adjust front to rear balance. Wilwood tandem master cylinder #260-8794 works well for most applications.
  7. Replies
    15
    Views
    1,263

    Yes, It will probably cost way more to finish...

    Yes, It will probably cost way more to finish that the car can ever be sold for. Better to sell as is and get what you can.
  8. A stop on the clutch pedal is a good idea to...

    A stop on the clutch pedal is a good idea to eliminate over extending the slave cylinder. Usually the master cylinder bore is smaller than the slave. This gives a lighter pedal feel and the slave...
  9. Replies
    3
    Views
    690

    Lamboclone site

    Anyone else having a problem getting on the Lamboclone site? I get a message that says Account Suspended.
  10. Thread: suspension

    by txbuilder
    Replies
    21
    Views
    2,431

    The Factory Five GTM uses the C5 suspension and I...

    The Factory Five GTM uses the C5 suspension and I hear the C6 is pretty much the same. The only thing I have against the Corvette suspension parts is that they are rather bulky and heavier than...
  11. Replies
    12
    Views
    1,305

    You are describing a Lotus 7 type car. You can...

    You are describing a Lotus 7 type car. You can update the body to something like the Maxton was but then you get in to more complicated body work. Just do a 7 and be done with it.
  12. Replies
    299
    Views
    102,250

    I don't know much about electronically shifter...

    I don't know much about electronically shifter automatic transmissions but have been told that the Porsche needs inputs from the engine as well as other places to shift correctly. If this unit can...
  13. Replies
    299
    Views
    102,250

    I have made adapters for the Chrysler 42LE and...

    I have made adapters for the Chrysler 42LE and the ZF 5HP19. The issue is getting a controller to shift them.
  14. Replies
    299
    Views
    102,250

    If you plan on running 500 HP or doing any sort...

    If you plan on running 500 HP or doing any sort of racing expect to pay at least $15,000 for a good transmission. There is really no way to do this cheap. The G50s will cost you at least $10,000...
  15. It takes a fair bit of HP to run a compressor so...

    It takes a fair bit of HP to run a compressor so a motor designed for that would be best. Make sure your alternator makes enough amps to run it.
  16. Replies
    1
    Views
    750

    I still have two sets of these available if...

    I still have two sets of these available if anyone is interested.
  17. Replies
    4
    Views
    1,240

    That drivetrain makes for some serious rear...

    That drivetrain makes for some serious rear weight bias so be careful driving that thing.
  18. Replies
    1
    Views
    750

    V12 header flanges for sale

    I have header flanges to fit the BMW V12 engine. A set of 4 is required for each engine. PM me or email to eric@kitcarchassis.com. Photos here:...
  19. Replies
    55
    Views
    21,313

    To Soldier9394. I have tried replying to your PM...

    To Soldier9394. I have tried replying to your PM but I don't know if it has gone through as nothing shows up in my sent folder. email me at eric@kitcarchassis.com with any questions you have.
  20. Replies
    55
    Views
    21,313

    I make adapters for both the LS engines and the...

    I make adapters for both the LS engines and the BMW V12 to the Boxster transmission. It would be quite a bit of work to make the LS adapter fit the BMW. Better to start from scratch and do a new...
  21. Replies
    5
    Views
    2,978

    This thread is 7 years old so probably not much...

    This thread is 7 years old so probably not much use looking for information here.
  22. Replies
    45
    Views
    20,388

    So it's front wheel drive?

    So it's front wheel drive?
  23. Replies
    29
    Views
    7,638

    For anyone who needs a shifter for the 016, 01E...

    For anyone who needs a shifter for the 016, 01E or 01X I have them. PM me here or email to eric@kitcarchassis.com
  24. Replies
    1
    Views
    648

    How about a little more information. What...

    How about a little more information. What transmission and what shifter? Did it work OK before you changed the cables? If it is not going all the way into reverse you can probably lengthen the...
  25. Replies
    9
    Views
    2,409

    Lloyd lives just a few miles from me. He lost a...

    Lloyd lives just a few miles from me. He lost a leg in a motorcycle accident a couple of winters ago and is not doing any car work at this time. He does have some Fiero parts for sale including...
Results 1 to 25 of 267
Page 1 of 11 1 2 3 4