Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Fiero cradle bushings

  1. #1

    Fiero cradle bushings

    Has anone replaced Fiero cradle bushings before? Any tricks I should know about before I get started?

  2. #2
    Senior Member MacGyver's Avatar
    Join Date
    Dec 2004
    Posts
    3,055

    Re: Fiero cradle bushings

    I think I remember reading a while back where thay can be replaced with polly for better handling.

  3. #3

    Re: Fiero cradle bushings

    Quote Originally Posted by MacGyver
    I think I remember reading a while back where thay can be replaced with polly for better handling.
    Yes, I have a set of the poly ones, I just didn't know if there was a trick to getting the old ones out. It doesn't look real easy.

  4. #4
    Senior Member MacGyver's Avatar
    Join Date
    Dec 2004
    Posts
    3,055

    Re: Fiero cradle bushings

    Looks like Pennock's has a few talking about it. Your correct. Doesn't look easy. Better have a 6 pack handy!

  5. #5

    Re: Fiero cradle bushings

    Quote Originally Posted by MacGyver
    Looks like Pennock's has a few talking about it. Your correct. Doesn't look easy. Better have a 6 pack handy!
    Thanks Mac. I rarely go to Pennocks. I guess I need to spend some more time over there.

  6. #6
    Moderator FunnyWheels's Avatar
    Join Date
    Nov 2002
    Location
    Tampa, FL
    Posts
    8,151

    Re: Fiero cradle bushings

    It is easy to do. All you need is a jack and socket. Make sure you do both sides at the same time
    If you're not confused, you're not paying attention.

  7. #7

    Re: Fiero cradle bushings

    Quote Originally Posted by FunnyWheels
    It is easy to do. All you need is a jack and socket. Make sure you do both sides at the same time
    Thanks Dave.

  8. #8
    Moderator FunnyWheels's Avatar
    Join Date
    Nov 2002
    Location
    Tampa, FL
    Posts
    8,151

    Re: Fiero cradle bushings

    You're wecome!
    If you're not confused, you're not paying attention.

  9. #9
    Senior Member sactodreamer's Avatar
    Join Date
    Oct 2003
    Location
    Sacramento, CA
    Posts
    2,270

    Re: Fiero cradle bushings

    I haven't gotten around to my craddle bushings yet but I figured I'd use the cheap little press I bought from Harbor Frieght.

  10. #10

    Re: Fiero cradle bushings

    Burn out the front ones with a propane torch. The rear ones just pry off.

    Joe Sokol 8)

Similar Threads

  1. 1988 Fiero v8 Engine cradle
    By CCIE in forum The Mall
    Replies: 0
    Last Post: 04-09-2011, 10:33 PM
  2. Fiero engine cradle for sale
    By DINERO in forum The Mall
    Replies: 0
    Last Post: 04-25-2009, 01:40 PM
  3. FS - Extended fiero cradle
    By Daleford in forum The Mall
    Replies: 0
    Last Post: 12-24-2006, 01:01 PM
  4. Extended kitcar/Fiero cradle on E-Bay
    By Daleford in forum The Mall
    Replies: 0
    Last Post: 12-06-2006, 07:59 AM
  5. Brand new Urethane bushings 85-87 Fiero
    By mikeo in forum The Mall
    Replies: 5
    Last Post: 11-23-2004, 05:44 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •