Page 1 of 3 123 LastLast
Results 1 to 10 of 27

Thread: Dimension needed - rear window opening AD355 Berlinetta

  1. #1
    Senior Member
    Join Date
    Dec 2002
    Location
    New England
    Posts
    1,637

    Dimension needed - rear window opening AD355 Berlinetta

    Can anyone tell me how tall this area needs to be (see photo below) in order to fit in the glass and any clearances needed? I want to make a support bar that goes just under the fiberglass but do not have the MR2 rear window yet.

    Thanks!!
    Attached Images Attached Images  

  2. #2
    Senior Member
    Join Date
    Dec 2002
    Location
    New England
    Posts
    1,637

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Still need this information.

  3. #3
    Senior Member ITALIANKNIGHTRIDER's Avatar
    Join Date
    Jan 2005
    Location
    Tx
    Posts
    2,995

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Mark has the rear window in plastic ,would you like to have one made, at material cost, plus shipping ,i sent my mr2 glass to him an it has been copied but after the mold tooling was made, none of the people asking about the rear glass placed orders ,they are clear as Original glass this kit use the mr2 back glass

    http://www.madmechanics.com/profile/?u=19409
    In the USA if you pay a company / person to start a plug, then it,s your plug and work ,it is not theirs to sell or trade !!

  4. #4
    Senior Member
    Join Date
    Dec 2002
    Location
    New England
    Posts
    1,637

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Thanks IKR. I will think about using Marks rear glass. I know he does good work as I have a set of his side glass already.

    If you have the glass there could you measure the height sometime this week so I can add in the reinforcements I wanted to add.

    Thanks.

  5. #5
    Moderator FunnyWheels's Avatar
    Join Date
    Nov 2002
    Location
    Tampa, FL
    Posts
    8,151

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Ask Brastic, he will know. He has a AD355.

    Dave
    If you're not confused, you're not paying attention.

  6. #6
    Senior Member
    Join Date
    May 2007
    Posts
    1,453

    Re: Dimension needed - rear window opening AD355 Berlinetta

    I've got an MR2 glass that hasn't been installed on my AD355 yet. What measurements are you looking for? (from which point to where, etc.)

  7. #7
    Senior Member
    Join Date
    Dec 2002
    Location
    New England
    Posts
    1,637

    Re: Dimension needed - rear window opening AD355 Berlinetta

    I need to know how tall the glass is in the center of the window. I can then add 1/4" on each side to get the opening size needed in the fiberglass.

    Thanks!

  8. #8
    Senior Member
    Join Date
    May 2007
    Posts
    1,453

    Re: Dimension needed - rear window opening AD355 Berlinetta

    in the center, from bottom of glass to top of glass = 9 1/2".
    off center on the left and on the right, from the bottom of glass to top of tab on MR2 glass = 9 7/8"


    ____/----\___________/----\_____
    / \
    / \
    /_______________________________\


  9. #9
    Senior Member
    Join Date
    Dec 2002
    Location
    New England
    Posts
    1,637

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Tabs.... I wasn't aware there were any tabs. Thanks for pointing that out and for the dimensions. You were a big help.

  10. #10

    Re: Dimension needed - rear window opening AD355 Berlinetta

    Quote Originally Posted by jntramey
    I've got an MR2 glass that hasn't been installed on my AD355 yet. What measurements are you looking for? (from which point to where, etc.)
    Out of curiosity, what is the width at the rear bottom tips... from left bottom to right bottom.

Similar Threads

  1. Jntramey's Amazing AD355 berlinetta build
    By jntramey in forum Build Diaries
    Replies: 411
    Last Post: 12-29-2017, 08:07 PM
  2. Pictures of AD355 spider/Berlinetta
    By NeoFreakTarma in forum General Kitcar Chat
    Replies: 9
    Last Post: 07-12-2012, 03:00 PM
  3. A semi custom AD355 Berlinetta build diary
    By Ferrari Berlinetta in forum Build Diaries
    Replies: 73
    Last Post: 07-12-2012, 02:53 PM
  4. FOR SALE: AD355 Berlinetta/spider kit
    By Ferrari Berlinetta in forum The Mall
    Replies: 7
    Last Post: 11-24-2011, 05:18 PM
  5. Replies: 0
    Last Post: 12-31-2008, 12:55 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •